HanSolo

Forum Replies Created

Viewing 30 posts - 31 through 60 (of 104 total)
  • Author
    Posts
  • in reply to: Does the CoolJet work okay if you don’t fill it all the way? #10077
    HanSoloHanSolo
    Participant

    Half full is fine for normal desk use. The only thing that changes is how long you can run it before the water runs out. It’s not like the cooling gets weaker just because there’s less water in there.

    in reply to: Qinux BlackOptic without an SD card, can you still use it? #10076
    HanSoloHanSolo
    Participant

    No card needed if you just want to look through it. I ran mine for a couple weeks without one before grabbing a card, used it around the yard and on a night hike, screen does what it needs to. The internal storage might hold a few snaps but it’s not worth relying on. Just know you’re buying a viewer until you get the card.

    in reply to: Does SynGas need a certain spot in the car to work well? #9989
    HanSoloHanSolo
    Participant

    Positioning really shouldn’t matter. It’s just reading data and sending its own signals back through the port. Mine sits sideways in a tight spot under the dash and it still adapted fine after the usual driving time. The only thing I’d avoid is letting it hang where your knee hits it constantly, but that’s more about the port breaking than the device working.

    in reply to: Does Back Restore work on a carpeted floor or does it slide around? #9195
    HanSoloHanSolo
    Participant

    Mine sits fine on the carpet in my bedroom. I don’t have to adjust it or anything while I’m using it. If you’re just lying there letting it do its thing, I think you’re fine.

    HanSoloHanSolo
    Participant

    Most of the break-in talk is just people overthinking it. Yeah, mine was a bit stiff for a couple nights, but it wasn’t like sleeping on a brick. If you’re used to regular pillows, it’ll feel different right away and that’s the point. Give it a week, not a month.

    HanSoloHanSolo
    Participant

    The position thing gets overthought. I get the concern because the idea of a card in a stack sounds like it should block everything, but that’s not really how it plays out in practice. The card is just sitting there with your other cards, it’s not like it needs direct contact with each one to do its job. The signal has to pass through the whole wallet anyway, so it either gets blocked or it doesn’t.

    I keep mine in the slot closest to the outside of the wallet, not even near the cards I actually use. That’s just where it ended up and I never bothered moving it. If it were that sensitive to exact placement, I figure I would have noticed by now, because I’ve been through plenty of crowded train stations and busy markets where people are brushing against you constantly. Nothing’s ever pinged on my card reader after the fact, and I check that stuff regularly.

    I think people expect this thing to work like some kind of force field with strict boundaries, but really it’s just a solid layer of material in the way. Stacking cards on top of it or having it off to the side doesn’t change the fact that it’s still in the wallet. Unless you’re carrying it in a separate pocket, which kind of defeats the point, it’s doing what it’s supposed to do. I would not lose sleep over where exactly it sits.

    in reply to: FitiBeats volume level on calls – is it just me? #8548
    HanSoloHanSolo
    Participant

    Call volume has been hit or miss for me depending on the device. On my laptop it’s fine, but on my phone it’s noticeably lower. Not a setting issue, just seems inconsistent.

    HanSoloHanSolo
    Participant

    Bring the spray. The light’s fine, but I wouldn’t bet the weekend on it.

    in reply to: Does Translattia work offline or is it mostly online? #7600
    HanSoloHanSolo
    Participant

    Offline mode is basic at best, so I wouldnt rely on it for a hike.

    HanSoloHanSolo
    Participant

    Direction is one of those things you only really notice when it’s wrong. I had mine half buried in a flower bed, angled sideways toward nothing in particular, and it still kept raccoons off the patio for weeks. Then I moved it to a bare spot near the back door and suddenly nothing changed. Still worked. So from my experience, the sensor isn’t as picky as the manual makes it sound.

    The solar panel is the part I’d actually worry about. If you face it away from the sun it’ll die out by evening and then it doesn’t matter where the sensor points. Mine sat in shade for two days and the LED barely blinked. So point it wherever, just make sure the panel gets decent light. That’s the only direction I’d obsess over.

    in reply to: Does the Melara Air sit too high for stomach sleepers? #7203
    HanSoloHanSolo
    Participant

    I’m a stomach sleeper too and had the same reaction at first. That lift felt more noticeable than any pillow I’ve used before. But after about three weeks I stopped noticing it. My neck stopped feeling like it was propped up and now it just feels normal.

    I don’t know if the foam softened up or if I just got used to the angle, but it did settle in. I still wouldn’t call it a perfect stomach sleeper pillow, but it’s not as bad as those first few nights made me think. If you’re only a few weeks in, I’d give it a bit more time before deciding. The shape is pretty fixed so if it still bugs you after a month it probably won’t change much.

    in reply to: Does the Hewelth UVClean need to be charged before first use? #6993
    HanSoloHanSolo
    Participant

    Charging it first is the safe move. Mine had a little juice but I didn’t trust it to finish a full cycle, so I plugged it in while I was doing the initial wash. It’s not like you can use it before cleaning it anyway.

    in reply to: Derila Ergo and pillowcases, do standard ones fit? #6956
    HanSoloHanSolo
    Participant

    Standard pillowcase will go on, no question. The problem is it never looks right and the fabric slides around the foam because of the weird contour. I gave up and just use the included cover, less hassle than fighting with a case that clearly wasn’t made for that shape.

    in reply to: Does the Qinux Vapoxis work okay on oven glass? #6771
    HanSoloHanSolo
    Participant

    It’s literally made for ovens, so I’d use it there without overthinking it.

    in reply to: Does the GrillWizz work on really old caked-on grates? #6763
    HanSoloHanSolo
    Participant

    It is a lot easier if you hit the grates while they are still warm. I let mine sit way too long once and the crust laughed at me for a while, but turning it up and letting the brush sit in one spot for a few seconds did the trick. It just takes longer than the videos make it look.

    in reply to: AerioQ remote control range issue or just me? #6564
    HanSoloHanSolo
    Participant

    The receiver on these units is pretty weak. I’ve noticed the same thing, mine basically needs line of sight or it just ignores the signal. Not a huge deal for me since I’m usually sitting nearby, but the range claims definitely oversell it.

    in reply to: Qinux BlackOptic SD card slot feels loose or is it just mine? #6502
    HanSoloHanSolo
    Participant

    Mine has some play in it too but I wouldnt call it loose enough to worry about. If the card stays put and the files actually save, it’s probably fine. These budget night vision units arent exactly precision instruments.

    in reply to: Coolizi Coolzy heating mode smell anything? #6294
    HanSoloHanSolo
    Participant

    Yeah, that dusty smell is pretty much what you get on these dual mode units. The heat exchanger or whatever sits there doing nothing for months while you run cooling, so dust collects on it. First time the heating kicks in, it burns off. Same thing happens with space heaters that’ve been in storage.

    Mine did that too. Noticed it more the first couple of times I switched over. After maybe the third or fourth use it was barely there. If it sticks around after a week of regular heating use, then maybe I’d start wondering. But right now I wouldn’t stress over it.

    Probably worth just running it on heat for a bit with a window cracked if it bothers you. Let it burn through whatever’s on there. I didn’t think much of it at the time, just figured it was normal for something that switches between hot and cold.

    in reply to: Does the ResQVac mask fit snugly on a small adult? #6238
    HanSoloHanSolo
    Participant

    The whole “adult mask won’t fit small faces” thing gets blown out of proportion. I’m not exactly built like a linebacker myself, and I’ve had no problem getting a seal when I’ve practiced with mine. The mask is flexible enough that it molds a bit when you push down, which is the whole point of the “place” step. It’s not like a rigid CPR mask that just sits on top.

    I get the concern, but people overthink the sizing. If it’s literally falling off, sure, use the child one. But for most smaller adults, the adult mask pressing down firmly is going to do the job. Choking emergencies aren’t exactly the moment for a perfect custom fit anyway.

    in reply to: Qinux BreezaMax vs old desk fan for noise at night? #5947
    HanSoloHanSolo
    Participant

    Honestly, I wouldn’t overthink the noise thing. If your old fan sounds like a jet, this will be a big step up even if it’s not dead silent.

    HanSoloHanSolo
    Participant

    I think they include a few sizes, small included. Fit is usually the gamble with these things no matter what they toss in the box though.

    in reply to: Anyone using the Qinux Zindoggo? #5859
    HanSoloHanSolo
    Participant

    Battery sounds about right for a GPS collar that’s actually polling. I’d just top it off after every walk and not worry too much unless it starts dying mid-day.

    in reply to: How do you hold the Qinux Gravizer for longer projects? #5554
    HanSoloHanSolo
    Participant

    It’s a pen, not a jackhammer. Just take a break or switch hands if it bugs you that much.

    HanSoloHanSolo
    Participant

    I’d take the hydrophobic claim with a grain of salt. Most sprays like that lose the water beading pretty quick once you hit them with soap a few times.

    HanSoloHanSolo
    Participant

    I’d bet the flickering thing is just coincidence. Those lights are usually just reacting to whatever the washer or fridge is doing at that moment.

    in reply to: Qinux BarkBuz for a stubborn barker? #4638
    HanSoloHanSolo
    Participant

    Hard to say with a really stubborn dog. I have one that ignores most things and it sort of worked for a bit then he got used to it. Might be worth a shot if you can borrow one first. Not totally sure it’ll fix a neighbor’s problem though, depends on the dog.

    in reply to: Qinux VultrioX on uneven ground – any tips? #4583
    HanSoloHanSolo
    Participant

    I think it might just be how these wire heads react when the ground isn’t perfectly level. Not totally sure there’s a fix for it.

    HanSoloHanSolo
    Participant

    I’d say it’s probably doing something. I’ve had mine for a while and I definitely notice fewer mosquitoes buzzing around the living room at night compared to before. Not a massive difference, but it’s not nothing either.

    in reply to: DrFlexa sizing question – how tight should the straps be? #4526
    HanSoloHanSolo
    Participant

    I just put mine on until it feels secure without being annoying. Too tight and you’ll hate it by lunch, too loose and it’s basically a leg warmer.

    in reply to: Does the Herz P1 Smart Scale need WiFi or just Bluetooth? #4410
    HanSoloHanSolo
    Participant

    Mine’s just Bluetooth, no WiFi needed. I set it up without any internet and it synced fine.

Viewing 30 posts - 31 through 60 (of 104 total)