Ben Harlow

Forum Replies Created

Viewing 24 posts - 31 through 54 (of 54 total)
  • Author
    Posts
  • Ben Harlow
    Member

    That twitchy feeling is the pulses actually hitting the muscle instead of just buzzing the skin. Lower settings barely do anything for me, they just feel like a light tickle. Once I get it up there, yeah, it gets that sharp, involuntary spasm thing going. That part is pretty standard for this type of unit honestly.

    I do think the prickly part is the part I’d watch. The twitching is one thing, but if it feels like needles or like it’s biting your skin, the pads might not be seated flat enough against your neck. If the contact is uneven, it concentrates the current into one spot and that feels nasty.

    Try making sure the gel pads are damp enough and the wrap is snug, not loose. I noticed mine gets prickly when it shifts around. If it still feels like pins after adjusting the fit, that’s when I’d back it down a level because that sensation isn’t going to go away with more use.

    in reply to: How does Omnihear handle outdoor wind noise? #9543
    Ben Harlow
    Member

    Wind noise is still wind noise no matter what mode you pick.

    in reply to: Can the Qinux BreezaMax sit on a nightstand without tipping over? #9542
    Ben Harlow
    Member

    You’re getting a lot of “mine was fine” answers, but mine wasn’t. I had it on a nightstand for about a week and the cat brushing against it was enough to knock it over twice. The base is wide but it’s light, so it doesn’t take much. The second time it hit the floor it stopped oscillating properly.

    If your cat is the type to jump up on furniture or squeeze behind things, I would not trust this thing on a narrow surface. It’s fine on a desk or a proper table where nothing is going to bump it, but bedside with a pet around is a different story. I moved mine to a shelf after that and it’s been fine, but I wouldn’t have bought it for the nightstand if I’d known. Just something to think about before you order.

    in reply to: Do the SonaBuds pick up background noise during calls? #9477
    Ben Harlow
    Member

    The whole background noise thing really depends on where you are. I’ve seen people treat “noise cancellation” like it’s magic, but with these it’s mostly about the mics picking up your voice clearly, not silencing the world around you. If you’re on a train or a busy street, the person on the other end will still hear some of that rumble. It’s not like the SonaBuds turn your surroundings off.

    What I noticed with mine is that they do a decent job in a moderately loud café, but the moment you get into heavy traffic or a crowded terminal, you might as well be holding the phone normally. The other person will still hear you, but they’ll hear the background too. So if your main concern is being in loud spaces, these aren’t going to fix that. They’re fine for a quiet room or a stroll, but don’t expect them to work like a dedicated call headset.

    Ben Harlow
    Member

    It helps with new stains, not the ones that have been baking in for years. I noticed a difference within a few weeks of using it on my front teeth, but I also wasn’t expecting a miracle. If you’re diligent with it, it does the job.

    in reply to: Does the iTagPro beep as loud as the old Tile? #8806
    Ben Harlow
    Member

    I can’t say I’ve done a side-by-side comparison with a Tile, but I do remember the Tile being annoyingly loud. The iTagPro is definitely more of a polite chirp than a shout. I keep mine on my keys and I’ve missed it a couple times when it’s buried in a jacket pocket, whereas the old Tile cut through that no problem. For me, it’s actually a plus, I don’t need the whole house hearing my stuff beep. But if you’re relying on it to find things from across the room, you might be doing a bit more walking than you used to.

    Ben Harlow
    Member

    Mine was comfortable from the first night, but I think that’s because I’m not picky about pillows at all. I just put my head down and sleep. I never understood the whole “my neck is searching for something” thing. It’s a pillow. If you wake up without pain, it’s doing its job.

    The only thing I noticed was that the shape is smaller than what I was used to. Took me a second to stop reaching for extra pillow in the middle of the night. But that’s more of a habit thing than a comfort thing.

    I’ve seen people on here talking about needing a week or more to adjust. I don’t buy it. Either your neck feels better or it doesn’t. If you’re still fiddling with it after a few nights, maybe it’s just not the right fit for you. No shame in that.

    in reply to: Is it normal for the Ozoori to feel warm after Boost Mode? #8684
    Ben Harlow
    Member

    Boost mode runs harder, so it warming up some is pretty basic physics. Mine’s been doing that since I got it and it’s still working fine months later. I’d only start paying attention if it feels genuinely hot, not just warm.

    Ben Harlow
    Member

    The auto-recognition is just matching weight, so if you two are nearly identical it’s a toss-up. I would not rely on it to pick the right profile every time. You’re better off picking your profile manually in the app before you step on. It’s annoying but it beats fixing the data later.

    Ben Harlow
    Member

    Different device but same idea. I grabbed one of those older units a while back and the manual carrier picking got old fast. The Ryoko just connects when you turn it on and that’s it. I stopped carrying the other one entirely. So no, it’s not just a nicer app.

    in reply to: AerioQ cooling mode leaving the room a bit damp? #8340
    Ben Harlow
    Member

    Mine does the same thing. Noticed it after running it for a few hours on a humid day. The air felt heavier than before I switched it on. I just assumed it’s how the thing works and stopped caring.

    in reply to: Qinux Vibrathea battery life after a few months? #8245
    Ben Harlow
    Member

    Battery drop after a couple months is pretty standard for anything rechargeable, especially if you’re using the heat mode. I’m more annoyed that the pads lose stickiness way before the battery becomes an issue. I’d take shorter battery life over having to replace those things every few weeks.

    Ben Harlow
    Member

    Spray’s still the backup plan; that thing is just a fancy lantern if the bugs are serious.

    in reply to: Does the Qinux BreezaMax really work well for a small bedroom? #7842
    Ben Harlow
    Member

    For a 10 square meter room it should be fine. I wouldn’t expect it to blast you out of bed, but it moves enough air to keep things comfortable. The quiet part is the main reason I’d pick it over a regular fan.

    in reply to: Ozoori placement in a small fridge, any spots that work better? #7657
    Ben Harlow
    Member

    I just set mine on the top shelf wherever there’s room and called it a day. It’s been a couple weeks now and honestly the fridge doesn’t smell like last week’s fish anymore, so I’m not about to overthink placement. If it works on the shelf, it probably works wherever you put it.

    in reply to: SleepZee fit after a few weeks, does it loosen up? #7069
    Ben Harlow
    Member

    It loosens, but not by much. Mine stayed pretty rigid for the first few weeks and then just softened a little around the edges. It never turned into a loose fit, just less like a brick in the mouth. If you want it to feel noticeably bigger, you might be waiting a while.

    Ben Harlow
    Member

    Mine does the same thing. I think it’s just the compressor cycling, like a fridge. Not something I’d worry about unless it stops cooling altogether.

    in reply to: TrimZa for kids? #6492
    Ben Harlow
    Member

    It’s fine for kids but I wouldn’t expect it to be some kind of miracle tool. You still have to be patient and actually watch what you’re doing. Works better for small nails than I thought, but it’s not faster than just doing it normally.

    in reply to: Coolizi Coolzy heating mode smell anything? #6180
    Ben Harlow
    Member

    First time I flipped mine to heat it did the same thing. Smelled like the inside of an old vacuum bag for a bit. I figured it was just dust that settled on the heating element while it sat in storage or whatever.

    It went away after the second or third use for me. Hasn’t come back since. If it’s a brand new unit, there’s also that “new appliance” smell that can linger for a bit. I wouldn’t worry about it unless it starts smelling like burning plastic or something actually acrid. That would be a different story.

    As long as it clears up after a few cycles, I’d just run it and not think about it. Mine’s been fine for a couple months now.

    in reply to: Wood Ranger Power Leaf Blower ok for blowing off a deck? #5802
    Ben Harlow
    Member

    15 minutes sounds like enough for blowing off a deck. I think you’d have to be pretty slow for it to be an issue.

    in reply to: How do you hold the Qinux Gravizer for longer projects? #5563
    Ben Harlow
    Member

    It’s just a bit heavy for long sessions. I don’t think you really get used to it, I just do shorter bursts.

    Ben Harlow
    Member

    Guess that answers it. The heat is barely there for me too but if other people notice it more in a cold room then I guess it’s not broken. Whatever, the traction is what I bought it for anyway.

    in reply to: Can the Nunawave Oral Care Pro be used if you have braces? #4911
    Ben Harlow
    Member

    I’d probably wait until the braces are off. The mouthguard needs to fit snugly and brackets will just get in the way or make it uncomfortable. Not worth the hassle.

    in reply to: NanoPolix on single stage paint? #4842
    Ben Harlow
    Member

    It’s single stage, so it’ll probably work fine for light oxidation. I wouldn’t expect a miracle, but it’s not going to wreck the paint.

Viewing 24 posts - 31 through 54 (of 54 total)