Forum Replies Created
-
Posts
-
A dim projector isn’t really the screen’s problem, so I’d give it a shot with what you already have. Mine looks fine at night even though my projector is nothing fancy, and the screen definitely helps compared to a bare wall. If the picture still feels weak, that’s coming from the projector itself, not the screen.
Bare skin is where mine stays, but for a different reason than the heat or pulse thing. I noticed the wrap slides down less when I wear it against my neck, especially if I’m doing dishes or tidying up. Over a shirt it kept creeping up on me and I’d have to keep tugging it back into place.
I still use mine with an iPhone XR and the connection has been fine for music and calls. The app feels a little slow to load sometimes, though once it’s open everything runs smoothly. It’s honestly been smoother than my old earbuds were.
Late morning breeze is probably doing more than you think, even a light one adds that little wobble to every nose turn. If you do try the evening session, I’d pick a day where the trees look completely still from the ground before you even launch, since sunset can look calm and still have air moving higher up. The buggy park thing is fair though, I usually fly in a field with nothing around so dusk is easier for me. One thing that helped me judge it, I started doing the same slow turn at the start of every flight so I had something to compare instead of guessing whether it was the air or me. Kind of boring but it made the difference obvious. Report back after the evening flight, curious if it lines up with what you saw at sunset.
I mostly shoot straight-ahead stuff for that exact reason, pans on mine look fine until I actually turn the nose, then it gets twitchy. Have you tried filming in the calmer part of the evening? That made more difference for me than anything on the sticks.
Mine never did that on soft mode, so I’d look at technique before blaming the tool. I mostly use the flat tip on the front teeth and skip the gumline entirely. Sensitivity that lingers an hour sounds like too much time in one spot.
Mine actually needs the app the first time before the buttons do anything, which caught me off guard since I figured it was plug and play. After that first pairing though it’s been fine on its own. Worth doing that setup at home before you head out.
Mine sits right next to a stack of printer paper and a spare monitor and I haven’t had any issues with it after a couple months of daily use. The paper doesn’t even feel warm unless I put it right in front of the vent, and it’s usually a good foot or so away. It’s a small heater so it’s not throwing heat far like a bigger unit would.
I just do both and it works fine for us. Subscription covers most of the week and I cook a little on Sundays when I have the energy. Keeps the routine simple without giving up the homemade thing entirely.
I went the other direction and actually added a couple of things that need the cloud less, since relying on the physical switch every time got old fast. Not a full overhaul, just swapped the worst offenders over time. Anyway, good to know I’m not the only one who noticed the app just dies.
Good mix of things to think about here. I’m going to keep an eye on the loose battery and charger situation before I commit to anything, that part makes a lot of sense to me. Thanks for all the input, this gave me plenty to chew on while I set the room up.
I usually notice a real effect within the first few minutes, like my shoulders dropping or my breathing slowing down without me trying. If I have to keep asking myself whether it’s working, that’s my answer. The light modes I can take or leave, but the vibration one I actually felt in my jaw, which surprised me.
I’ve had mine since March and never touch any special mode for games. The audio stays close enough for me, and I play a lot of puzzle and card stuff on my phone.
Nine really isn’t that old for a lot of dogs, so I wouldn’t just write it off as age. Mine went through a sleepy phase around that age and it turned out to be a low thyroid thing that a simple blood test caught. Not saying that’s your situation, but the change in walk interest is the part I’d pay attention to.
I’ve been on both sides of this with a mower I used for about six seasons on a half-acre yard, and the one year I skipped doing anything at all, I paid for it. Not right away either, which is what fooled me. It fired up okay in spring, ran rough for a couple of mows, then mid-summer it just quit on me and the shop told me the carb was gummed up from old fuel sitting in there. That repair cost more than a bottle of stabilizer, so now I at least add some before the last cut or two. I don’t bother running it completely dry because I never seem to time it right and end up with a half tank anyway.
What I’ve noticed is that the fuel itself matters too. The last couple years I’ve been buying the smaller cans of gas instead of filling a big jerrycan that sits in the garage forever, and that alone seems to have helped. Fresh gas going in plus a splash of stabilizer has been my routine and the mower starts on the first or second pull every spring now.
So yeah, for a basic push mower I think a little effort at the end of the season goes a long way. You don’t have to go full ritual with it, but doing nothing at all is the one approach that bit me. Curious whether anyone else noticed the old gas being the real culprit versus just the sitting time.
We just run ours in the bathroom and laundry room where there are outlets, and I’ve never once felt the need to haul it into a closet. If there’s no plug in there, that’s just how it is, and I don’t think that makes the whole thing pointless.
I kind of disagree with the whole “it’s just a narrower stream” thing. Narrower is the point, that’s how these things work without a motor. I’ve had cheap ones that cracked in a month though, so build quality matters way more than the pressure claims.
I just leave mine plugged in for most of the session and haven’t had any cutoffs or weirdness. The vibration and heat both stay steady, so I don’t see why you couldn’t. If it’s convenient, go for it.
That warmth creeping up partway through a session is just kind of how these heat pads behave in my experience. They don’t hold one steady temp for the whole run, they keep building a bit as the session goes on. So noticing it around the 10 minute mark lines up with that, it’s not you doing anything wrong.
What works for me is treating it more like a curve than a set and forget thing. I’ll start on a higher setting for the first several minutes while my back is still tight, then bump it down once things loosen up. By the time the session wraps I’m usually on the lowest setting and it feels about right. Turning it off early works too but I’d rather ride it out on low and get the full time in.
One thing I’ve learned is the warmth feels stronger depending on what surface I’m on. On the bed it’s milder for me than on the floor, same setting and everything. So if it’s bugging you, that might be worth messing with before you assume the unit runs hot.
I actually ended up moving mine to the inside of my case instead. Not for the looks, but because the tablet lives in a folio most of the time anyway and I figured if I was going to see a rectangle every time I flipped it open, I might as well stick it somewhere I don’t stare at. On a white back it’s just kind of there, and for me that got old faster than I expected. Everyone’s different on that front though.
The thing I’d actually pay attention to is whether you’re using a case. Mine sits under a clear-ish shell on one device and you can sort of see the outline through it, which honestly looks a little stranger than it did on the bare back. On the tablet I left it exposed and after a couple of weeks I mostly forgot it existed until I handed the thing to someone else and they asked what the sticker was. So it’s less about me noticing and more about other people noticing, if that makes sense.
If it were me, I’d leave it where it is for a bit and see if it fades into the background for you. If you’re still bugged by it after a week or two, that’s probably your answer and you can peel it and re-stick it somewhere less visible, like the inside of a case or the bottom edge. I did that with one of mine and it stuck fine the second time, no drama. Just don’t rush the decision while it still feels new.
Mine actually did fine in a drafty front room, which surprised me after reading all the doom and gloom. It ran more than usual, sure, but the room stayed comfortable enough. I left it going most evenings that first winter and didn’t notice a scary jump in the bill.
I mostly sharpened by hand before this, and I was expecting the Klampero to be kind of a gimmick that only helped if the chain was already in decent shape. Turned out to be the opposite for me. My chain was past the point where I’d normally just swap it out, and I got a solid session of cutting out of it after running the tool over every tooth a few times. Not a brand new chain by any means, but it stopped wandering in the cut and stopped throwing dust.
The thing that surprised me is how much it helped with consistency. When I sharpened freehand I’d always end up with a couple of teeth that were shorter than the rest, and the chain would cut crooked after a while. With the guide holding the angle I didn’t have that problem nearly as much. So for a chain that’s dull but not destroyed, I’d say it’s worth the time.
Where I’d be careful is if the teeth are really worn down to nubs or you’ve hit a rock or fence and chipped a bunch of them. No guided file is bringing those back, you need to take material off and that’s a different job. But for a chain that’s just been used a lot and lost its edge, mine came back fine.
I’ve run mine maybe four or five times now on two different chains and it’s held up okay. Still on the original file. Not sure how many sharpenings I’ll get before I need to swap that out, but so far so good.
I kind of disagree with the idea that the phone is optional for everything. Mine flies fine with the remote, but I still plug in my phone for the first minute just to check battery. Takes two seconds and saves me guessing.
I actually switched to a cordless one last year and my fine lines did get better, but mostly because I stopped fighting the cable dragging across the work. The Gravizer is light enough that I can hold it like a pen, which matters more for tiny letters than anything else. For simple gift stuff it’s plenty.
Morning sun only has been fine for mine, it still runs overnight. I think the all day sun thing gets overstated a bit.
