Qinux WarmPro clicking sound when it turns on?

That click is just the internal switch doing its thing before the heat kicks in. I’ve had mine since around late fall and it does the same little snap every time I flip it on, usually a second or two before I feel anything warm. First couple of weeks I barely noticed it, then one night it was dead quiet in the room and I heard it clear as day. Nothing changed after that, it kept heating the same way, so I stopped paying attention to it. What got me was the fan spinning up right after, that’s actually louder than the click in my case. If the heat still comes through fine, that’s the part that matters to me.

Mine clicks too and I’ve had it since winter started, still going strong. The click actually helps me know it’s kicked in without staring at it. Does yours click once or a couple times when you first plug it in?

Good to know it’s just the one click for you too. I’ve stopped paying attention to it at this point since mine’s been doing it since day one and hasn’t changed.

Mine does the same little click and I’ve just accepted it as part of the startup routine. What I noticed with mine is that the click comes first and then the fan sort of ramps up a second later, so the order is always the same. I’ve had it a few months now and it hasn’t changed or gotten louder, which is the part I actually pay attention to. If it started clicking repeatedly or clicking without any heat after, that would be my cue to look closer. For now it just sounds like a normal mechanical thing happening inside before the warm air arrives. Curious whether yours clicks once or a few times before it gets going?

The months part is honestly what made me stop noticing it. Mine clicked the same way for probably the first couple weeks and then my brain just filed it under normal background noise. What I pay attention to now is whether the warm air still shows up right after, and so far that timing has stayed exactly the same. If the gap between the click and the heat ever stretched out, that’s when I’d start paying closer attention. For now yours sounds like it’s doing the same thing mine did early on, and it settled into being predictable rather than getting worse. That consistency over time is really the useful bit, not the click itself.

A click on its own doesn’t bother me at all, but I don’t think it’s worth brushing off if it’s the only noise you hear. What I’d pay attention to is whether the fan sound comes on right after it. On mine the click and the fan start are close together, so if the click ever happens and the air stays cold, that’s when I’d look into it.

The click on mine happens right when I plug it in, before I even press anything, and it’s been doing that since day one. If yours only clicks when it starts heating, that’s a slightly different pattern than what I get. Does it ever click again while it’s running, or just the once at startup?

Ah okay, so the click is tied to the heat kicking on rather than the plug itself. That lines up with it being a normal switch sound then. Mine’s been clicking at the plug for a while now and it’s still going strong, so the startup one sounds like the same kind of thing.

Mine doesn’t click at all, it just starts blowing warm air after a few seconds. Not saying yours is broken, but it’s not something every unit does. Maybe it depends on the batch or how the internal switch is set up.

Mine clicks and then the fan kicks in a second later, so it’s just part of the startup for me. Doesn’t bother me, but I’ve only had it a couple months.

I’d unplug it and give the prongs a quick look, just to rule out anything loose at the outlet. If that’s all fine, I’d probably just use it as usual and see if the click stays the same over the next few weeks. Mine’s been doing its little startup noise since day one and hasn’t changed.

Mine’s done a little click since day one and it’s still going strong months later. A soft click on startup doesn’t really strike me as a red flag, more like the thing just waking up. If it’s still heating fine, I’d treat the sound as part of the routine.

I don’t think a startup click is something to write off. Mine was silent for the first couple weeks, then started clicking every time, and the heat output dropped soon after. If you’re still within the return window, that might be worth checking.

Mine has never clicked at all, and it’s been in daily use since I got it a few months back. If the click showed up right away I’d be looking at the plug connection first, not assuming it’s just normal.